SAWMILL & MOBILE EQUIPMENT

PAST AUCTION

WESTERN INTERIOR FIBRE INC.

AUCTION CLOSES: WEDNESDAY, JUNE 10TH, 2026

PREVIEW: Tuesday, June 9th, 9am-4pm By Appointment- Call 6043188433 To Schedule

Location: 9411 Northern Crescent, Prince George, BC

TO REGISTER TO BID CLICK THE LINK BELOW:

Bidspotter

Western Interior Fibre Inc. – Asset List

• 2009 Bandit Model 3680 “Beast” Horizontal Grinder, 500hp, S/N 1711 w/ Infeedand Outfeed systems; WEG Duty Soft Start  w/ Siemens electrical box;      
• Economizer Wood Processor, S/n MME0071194; 220V; w/ Power Pack;  
• Economizer Wood Processor, S/n 711757922;   
• Economizer Log Infeed Deck, 3 runs chain transfer, 12’W x 21’L, w/ 3HP motor, 464V 1760 RPM 182T frame & Highfield No. 5 reducer, 40/1 ratio; 
• 1994 Link Belt HLB2538 Excavator w/ Weldco WBM Butt N’ Top Grapple  

Sawmill 

• Log Infeed Deck, 18’W x 17’L; 10HP motor, 575V 1730RPM ; 215T Frame; w/ Highfield #8 Reducer, Type HU; 40/1 ratio 
• 7 Arm Hydraulic Log Kicker 
• Hourglass Log Positioning Rollcase; 7 Rolls, 16” Diameter x 30”L 
• Incline Log Cut-off Saw Deck; Circular 54” Log Saw; 30HP 575V 1750 RPM Saw Drive; 4 run flyted chain transfer; 10HP 575V 1755 RPM motor & Highfield No. 6 Reducer, 40/1 ratio  
• 10HP Motor, 575V 1730 RPM; Highfield No. 6 Reducer, 40/1 Ratio Secondary Log Infeed Deck to Slasher Saw; 2 run chain transfer, 9’W x 19’L; Est. 10HP motor, 575V & #12 Reducer  
• 5 Arm Hydraulic Log Kicker to barker infeed chain 
• Log Infeed Chain Conveyor to Slasher Saw; 10”W flat plate on chain x 60”L; p/w est. #8 reducer only  
• Powell 50” Slasher Saw; 40HP drive motor; 575V 1180RPM;  
• Waste conveyor under cut-off saw; 16” x 48’; 10” flighted box chain; Baldor 5HP motor, 1750 RPM 575V; 184T frame & Highfield No. 5 Reducer; 31/3 ratio; Type HV;  
• Cambio 18" 6 arm Debarker, Type CS-45; s/n 69540; spare parts, etc; Powell Debarker Base Structure 
• Debarker Infeed Chain from slasher saw; 10” flat plate on chain x 21’L; (2) 30” Hydraulic Log Sweeps 
• Powell control booth, operator controls & setworks  
• Powell Debarker Outfeed Chain Transfer, 13'6" x 30'; to scragg infeed  
• Catwalk for cut-off saw area  
• Powell 4 Saw Scragg System, Shifting Saws; 42” Blade; 16’ Max Log Length x 18” log diameter; 15’ Infeed w/ positioning rolls & (2) hold-down rolls; bottom double sharp chain through-feed; 15’ outfeed, (3) hold-down rolls; w/ (2) 3” slab chains in troughs; rough end roll to outfeed belt; Note: New linear slide bearings & shafts; PLC control   
• Scragg Outfeed Transfers 
• 3 Run camelback sort chain, 8'4" x 13'L; 4 arm hydraulic board spacer to Powell Gang Edger infeed; 3 Arm Jump Chain to Powell Board Edger infeed  
• 4 Run overhead 2-way return transfer, 10' x 6'L; drop to gang & board edger infeeds; chain or guides missing on overhead  
• Gang edger infeed, split infeed rolls, 5 each side, 15'L w/ line bar &  
• jump chains  
• (2) Powell Edgers 
• Powell 8” x 42" Gang edger, double arbour, 200 & 300 HP drives, 575V  
• Powell gang edger outfeed belt, 30" x 8'; 5HP 575V 1770 RPM & reducer; w/ rough live end roll (common drive)   
• Enclosure w/ Allen-Bradley 1336 Plus Variable Frequency Drive & Cutler-Hammer 6-16-2 NEMA Size 3 Starter  
• Board Edger Infeed Rollcase; 5 Roll 27" x 12'L  
• Powell 4” x 42” Board Edger; Single arbour; 60HP 575HP drive motor 
• Board edger outfeed belt, 24” x 8’; Motor & reducer 
• Board edger operator console 
• 3 Run camelback sorting transfer, 8' x 15'L  
• Pinch Roll Lateral Board Puller to return belt; Photo eye activated   
• Powell 11" x 15' incline return belt, motor & reducer   
• Powell Multi-Trim Saw: 0', 8', 10' & 4M saws; 2 set end saws, 2 middle jump saws; PLC control shared with edger;  
• 4 Run transfer to trim saw, 8' x 12'L  
• Trimmer Outfeed Decline Transfer, 3 run flighted chain to green chain, w/ drive 
• Green chain, 3 run H78 camelback chain; 10' x 56'L w/ rolloffs  
• Catwalk, stairs & railing inside mill  
• Log Bypass & Sorter Line 
• Box Chain Transfer, 11” x 120’L in 14”/21” trough; w/ drive; 
• Log Sort System, 195’L x (8) sort slides/bins (5 right, 3 left side); ScanMeg log scanner; Hydraulic tilt log offload; Ingvar Persson HPU, Model HAG-8-12/505;    

Chipping Area 

• Morbark Chip-Pak chipper system; 54” chipper; Est 75HP 575V; screen & fines blower;  
• Edem 30' vibrating chipper infeed conveyor, 60” fiberglass section   
• MDI CR-85 Metal Detector Control & Magnet  
• 48” Cyclone   
• BM&M 3’ x 8’6” Chip Screen  
• Blower above Economizer Wood Processor   
• Morbark Chip Bin Incline Conveyor, 24" x 110’L; w/ drives  
• Morbark Hog Bin Incline Conveyor; 18” x 110’L; w/ drives  
• Peerless Style Chip bin, 20 unit; Clamshell discharge gate 
• Peerless Style Hog bin, 20 unit; Clamshell discharge gate  
• Air blaster for hog bin  
• 5HP Hydraulic Power Unit; 1755 RPM 575V, 254T frame 

Electrics 

• Allen-Bradley 5 Section MCC; (21) Switches; Cutler-Hammer 4 Section MCC (Chipping); (15) switches, Including 400 amp chipper switch, (2) C-H NEMA Size 4 & (1) C-H Size 5 Starters; 400 Amp Gang Edger Switch; Wall of Switchgear to 400 Amp; Machinery related teck cable, transformers & more switchgear throughout mill; More… 

Compressor 

• 2011 Kaeser 75HP Rotary Screw Compressor, Model SFC-75S  
• Compair Twin Tower Desiccant Air Dryer, Model TW500; S/N 88-K4300;   
• 4’ x 12’ horizontal air tank  

Filing Room 

• Wright W150HD - A Top & Face Grinder  
• Wright W150DHD - B Top & Face Grinder  
• Wright W350 HD Auto Dual Ride Grinder; s/n 69416  
• Acme Post Grinder, Model BSA1100 
• Newman G-71 Guide & Babbit Grinder  
• Waage MP40A-6-2 Babbit Pot w/ chipper knife & saw guide jig; Extra guides  
• New Chipper Knives, (1) Box Simonds Cutter Knives & (4) Boxes New Chipper Knives;   
• Round saw bench anvil & anvil w/ stand; Stretcher roll; Spare 42” Saw Blades; Approx. (40) trim saw blades; Misc. spare hydraulics, motors, more… 
• Waste Conveyors 
• Trim block conveyor, 10" x 25'; w/ drive 
• Cross waste conveyor, 24" x 20'; w/ drive  
• Sawdust conveyor, 18" x 20' incline; w/ drive  
• Main waste, conveyor, 24" x 80'; 10” wings on chain  
• Waste conveyor from trim saw, 30'L  
• Chain chip conveyor from Beast Grinder; 24” x 15’L; 10” wings on chain 

Truck Scale 

• 2016 Precision ETS109090 Truck Scale, 10' x 100' x 92,000KG, w/ Western M2000 Digital Readout; s/n 11247, computer, printer, etc.  

PORTABLE SAWMILL  

• REMOVED FROM SALE- This item has been removed for repair to the electrical. Please contact Tradewest if interested once repair has been completed. 2012 Wood-Mizer LT-70 Sawmill, 36" x 40' Capacity, runs on 575V 3PH line power, with top mounted Yanmar 55HP diesel engine; Wood-mizer Log Bed, 40’ L incl. 24’ bed extension; Wood-mizer Log Infeed Transfer Deck, (4) Runs H78B chain; 12’L x 24’W; hydraulic drive from sawmill HPU;  

Baker Sawmill Pieces to be sold individually: 

• Baker Twin Vertical Band Scragg, w/ single horizontal saw; 575V; Model BSCR-0; w/ hydraulic power unit, Est 20HP;  
• Baker Twin Vertical Edger, (2) 20HP drives; 
• Baker Twin Horizontal Breakdown; (2) 30HP saw motors; 575V; Max 16” diameter x 16’ log; 
• Baker 12” x 9’ Rubber Conveyor Belt.